6 Reasons Why a Whirlpool Washing Machine is Leaking Water

6 Reasons Why a Whirlpool Washing Machine is Leaking Water
Table of Contents

Boost your skills in washer repairs with comprehensive articles such as

15 Common Whirlpool Washer Problems and How to Fix Them

Whirlpool Washer Not Spinning? 7 Common Causes & Solutions

6 Reasons Why a Whirlpool Washer Will Not Start

1. Damaged Door Gasket

When a Whirlpool washing machine is leaking water, a common culprit is a damaged door seal, also known as a gasket or bellow, which creates a watertight seal between the door and the drum.

Causes of Damage

  • Regular wear and tear from constant use.
  • Improper loading of clothes, putting strain on the seal.
  • Accidental damage from snagging clothing or objects during loading or unloading.

Diagnosing the Issue

  • Check for visible signs of damage like tears or cracks in the rubber material.
  • Observe water pooling around the front of the washer during operation or excessive moisture around the door area after a cycle.

Addressing the Problem

  • Promptly address a damaged door seal to prevent further complications.
  • Replacement can often be done through DIY washer repair with basic tools and model-specific instructions.
  • Obtain an appropriate replacement part from an authorized dealer or Whirlpool directly.

Understanding the potential issue with a damaged door seal and taking timely repair or replacement steps can effectively resolve water leakage in your Whirlpool washing machine, preventing future complications.

2. Faulty Water Inlet Valve

A common reason behind water leaks in Whirlpool washing machines is a malfunctioning water inlet valve. This component regulates water flow into the machine throughout the wash cycle.

Faulty Valve Symptoms

When the valve fails to close properly after water fills the machine, it can lead to continuous dripping or steady leakage.

  • Inadequate water supply to the tub during certain cycles can occur if the valve fails to open fully.
  • To troubleshoot a leaking washer due to a faulty water inlet valve:

Check Connections

  • Ensure all hose connections are tightly secured and free from damage or leaks.
  • Replace or repair any damaged connections.

Clear Blockages

  • Look for debris or sediment obstructing water flow through the valve.
  • Clean or remove any blockages.

Inspect Valve

  • If no obvious issues are found, inspect the water inlet valve itself.
  • Consider replacing the valve if necessary.

Always prioritize safety by disconnecting power and shutting off the water supply before attempting any repairs. Timely maintenance and repairs can prevent leaks and extend the washing machine’s lifespan. By addressing potential issues like clogged drain pumps or hose leaks, you can restore the washer’s functionality without costly professional repairs.

3. Leaking Hose Connections

Leaking hose connections are a frequent cause of water leakage in Whirlpool washing machines. These connections, responsible for water flow to and from different parts of the machine, can degrade over time or loosen due to various factors.

  • Troubleshooting should always involve checking hose connections, which often require simple maintenance.
  • Essential tools for washer repair include adjustable pliers for hose clamps and a flathead screwdriver for retaining clips.
  • Having a towel or bucket nearby helps contain spilled water during repairs.

Possible causes of hose connection leaks include wear and tear leading to small cracks or holes, loose connections due to vibrations or improper installation, and faulty seals or gaskets.

4. Clogged or Damaged Drain Pump

A clogged or damaged drain pump can cause water leakage in a Whirlpool washing machine, affecting its functionality during wash and spin cycles.

  • Debris accumulation like lint or coins can clog the pump’s impeller or hose over time, disrupting water flow and causing leaks.
  • Signs of a clogged pump include improper drainage or slow drainage, along with unusual noises during operation.

To troubleshoot, disconnect the power and locate the drain pump at the bottom front of the washer. Prepare towels and containers for potential water spillage.

  • Use appropriate tools like pliers or screwdrivers to disconnect hoses connected to the pump.
  • Inspect hoses for blockages, clearing debris with a soft brush or cloth.
  • Use compressed air cautiously to dislodge stubborn clogs, avoiding damage to components.
  • Clean the impeller of any visible debris and ensure it rotates freely without resistance. Replace if damaged.

Addressing drain pump issues promptly prevents further leakage and potential damage to other washer components. Regular maintenance, including cleaning and checking for blockages, minimizes the risk of clogs and ensures optimal washer performance.

5. Overloaded or Uneven Load

Overloading or unevenly balanced loads are common causes of water leakage in Whirlpool washing machines, exerting excessive pressure on components and leading to malfunctions.

  • Overloading the washer increases strain on components, potentially causing water leakage from various areas.
  • An overloaded load can result in an unbalanced drum during the spin cycle, leading to violent shaking and water spillage from weak points in the seal.
  • Stress from an uneven load can loosen or disconnect hoses and connections, contributing to water leakage.

To address this issue and prevent further damage, avoid overloading the drum and maintain a balanced load. Distribute laundry evenly before each cycle and consider reducing the number of clothes per washload if leakage problems persist.

6. Worn Out Tub Seal or Bearing

When dealing with water leakage in a Whirlpool washing machine, a common culprit is a worn-out tub seal or bearing. Constant friction and movement of components can lead to their deterioration over time, compromising the machine’s integrity.

  • The tub seal and bearing maintain a watertight seal between the outer tub and drive shaft assembly.
  • Prolonged use without maintenance can cause them to deteriorate, leading to water seepage during wash cycles or when the machine is idle.

Signs indicating a worn-out tub seal or bearing include unusual noises during operation, water stains near the bottom of the machine, or rust formation on internal components.

To address the issue, gather recommended repair tools such as pliers, screwdrivers (flat-head and Phillips), an adjustable wrench set, and a replacement tub seal and bearing kit specific to your Whirlpool model.


A leaking Whirlpool washing machine can be a frustrating and inconvenient problem to deal with. However, by understanding the common causes of water leakage and implementing the appropriate solutions, you can prevent further complications and ensure the efficient functioning of your washer. One possible cause of water leakage is a clogged or damaged drain pump.

Addressing issues such as faulty door seals, damaged water inlet valves, leaking hose connections, clogged drain pumps, uneven loads, worn-out tub seals or bearings are vital steps in troubleshooting and fixing water leakage in your Whirlpool washing machine. By consistently performing maintenance tasks like cleaning filters and inspecting vital components along with adhering to recommended loading practices will greatly enhance the efficiency and lifespan of your washer while minimizing instances of leaks.

Remember that maintaining an optimally functioning washing machine not only saves you from potential headaches but also contributes to the overall efficiency of your household chores, leaving you with more time and peace of mind. So, don’t hesitate to tackle washer issues head-on and enjoy the benefits of a leak-free laundry experience.


What are common causes of water leakage from a Whirlpool washing machine?

Common causes of water leakage from a Whirlpool washing machine may include issues with hoses, connections, damaged door seals, pump malfunctions, or problems with the tub seal and drain pump.

Can I troubleshoot and resolve issues with leaks around hoses or connections on my own?

Yes, you can troubleshoot and resolve issues with leaks around hoses or connections on your own. Inspect for loose connections, damaged hoses, or worn-out gaskets, and tighten or replace them accordingly.

Are there DIY solutions for problems related to damaged door seals or pump malfunctions causing leaks?

Yes, DIY solutions for problems related to damaged door seals or pump malfunctions causing leaks include inspecting and replacing faulty seals or pumps. Consult your user manual for specific guidance on your Whirlpool washer model.

How do I address issues with the tub seal or drain pump causing water leakage?

Address issues with the tub seal or drain pump causing water leakage by inspecting for visible damage, cleaning any debris, and replacing the faulty components. The user manual provides specific instructions based on your Whirlpool washer model.

When is it advisable to consult with a professional for Whirlpool washer water leakage issues?

Consult with a professional for Whirlpool washer water leakage issues if DIY solutions are unsuccessful, or if there are complex problems with internal components such as the tub seal or drain pump. Professional technicians can provide accurate diagnosis and appropriate solutions.

Share This Article

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top
Open chat
Scan the code
Get A Pro Chat *LIVE Agent*
Thank you for contacting Get A Pro! In a few words, let us know how we can help you. Please allow us 90 seconds to connect you to our live team member.